AIRLESSCO Prolight Contractor Series Instruction Manual download pdf (Page 3)

Fluids under high pressure from spray or leaks can

penetrate the skin and cause extremely serious injury,

including the need for amputation.

NEVER point spray gun at anyone or at any body part.

NEVER put hand or ngers over the spray tip. Do not use

rag or other materials over your ngers. Paint will penetrate

through material and into the hand.

NEVER try to stop or deect leaks with your hand or body.

NEVER wipe off build up around the spray tip.

ALWAYS remove the tip from the gun to clean it, after

following the PRESSURE RELIEF PROCEDURE!

NEVER operate spray gun under pressure without spray tip

ALWAYS remove tip from the gun to clean it.

NEVER try to "blow back" paint, it’s not an air sprayer.

If any uid appears to penetrate your skin, get

EMERGENCY CARE AT ONCE.

DO NOT TREAT AS A SIMPLE CUT.

• Go to an emergency room immediately.

• Tell the doctor you suspect an injection injury.

• Tell him what kind of material you were spraying with

and have him call for instructions at NATIONAL POISON

CENTER NETWORK (412) 681-6669

NEVER alter equipment in any manner.

NEVER use around children.

NEVER allow another person to use sprayer.

ALWAYS wear a spray mask while spraying.

NEVER LEAVE SPRAYER UNATTENDED WITH

PRESSURE IN THE SYSTEM. FOLLOW PRESSURE

RELIEF PROCEDURES ON PAGE 2.

ALWAYS set safety lock on the gun in "LOCKED" position

when not in use and before servicing or cleaning.

DO NOT remove or modify any part of gun.

CHECK operation of gun safety devices before each use.

NEVER work on gun when connected to hose.

INJECTION HAZARD

WARNINGS

GENERAL PRECAUTION

MEDICAL TREATMENT

SPRAY TIP SAFETY

TIP GUARD

SPRAY GUN SAFETY

Refer to pump manufacturer’s recommendation for

cleaning system. Release pressure from pump and hose,

remove spray tip and ush with lowest possible pressure.

CLEANING

NEVER operate gun without tip guard attached.

NEVER modify or alter tip guard.

NEVER use Airlessco tip guard on other attachments.

Airlessco’s tip guard is designed for use with standard

spray tips only. When using other than standard spray tips,

consult manufacturer of such attachment for recommended

tip guard & safety instructions.

Use extreme caution when cleaning or changing spray tips.

If spray tip clogs while spraying, engage gun safety latch.

ALWAYS follow PRESSURE RELIEF PROCEDURE

before removing spray tip to clean it.

Be very careful when removing hose or spray tip from gun.

A plugged line contains uid under pressure. If tip or line

is plugged, follow the Pressure RELIEF PROCEDURE for

the pump you’re using

FIRE EXPLOSION WARNING

SPRAYING VAPORS + STATIC SPARKING = FIRE/EXPLOSION

PREVENT FIRE AND EXPLOSION BY REDUCING STATIC SPARKING AND ELIMINATING VAPORS

ALWAYS be sure all equipment, paint bucket and object

being sprayed are properly grounded. ALWAYS ground

sprayer, gun, paint bucket and object being sprayed. Be

sure gun is grounded through hose connection.

NEVER spray in closed area. Ventilation must be

adequate to remove vapors.

NEVER keep ammable materials in spray area.

NEVER spray highly ammable liquids.

ALWAYS use high pressure conductive hoses with static

wire approved for 3000 psi. Never exceed 500 ft. of hose.

NEVER SMOKE IN SPRAYING AREA.

ALWAYS ensure properly maintained re extinguishing

equipment is available.

NEVER spray in vicinity of open ame or other sources of

ignition such as water heaters and furnaces.

ALWAYS locate the sprayer and electrical outlets in use at

least 25 feet away from spray area in well ventilated area.

Do not plug in any electrical cords in spray area. Follow

the coating and solvent manufacture’s safety precautions

and warnings.

HALOGENATED HYDROCARBON WARNING:

NEVER use halogenated hydrocarbon (HHC) solvents

or paints that contain them in this system. Some of the

most common of these solvents are: Carbontetrachloride,

Chlorobenzene, Dichloroethane, Dichloroethyl Ether, Ethyl

bromide, Ethylchloride, Tetrachloethane.

FLUSHING AND CLEANING CAN CREATE STATIC SPARKING IF DONE IMPROPERLY!

NEVER spray solvents under pressure through spray tip.

Follow PRESSURE RELIEF PROCEDURE and

remove spray tip for cleaning.Use LOWEST POSSIBLE

PRESSURE when ushing and cleaning.

Hold gun against metal container to reduce spark chance.

NEVER use cleaning solvents with ash points below 140

degrees F. Some of these are: acetone, benzene, ether,

gasoline, naphtha. Consult your supplier to be sure.

1 2 3 4 5 6 7 8 ... 11 12

Comments to this Manuals

No comments

AIRLESSCO Prolight Contractor Series Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Paint Sprayer AIRLESSCO Prolight Contractor Series