AIRLESSCO SL6500 Specifications

1001-818 APR08AIRLESS PAINT SPRAYERSERVICE/OPERATIONMANUALAIRLESSCOSL6500

89 3. Starting the Sprayer (see Fig. 6 & 7 above)a. Prime Valve must be open - priming position.b. Pressure Control Knob must be in low

894. Prime the Pumpa. Allow pump to operate until paint comes from gun.b. Release the trigger and engage the gun safety latch.c. Turn Prime

1011Leave prime valve OPEN until you are ready to spray again.4. Re-engage gun safety latchPRESSURE RELIEF PROCEDURETo avoid possible

1011AIRLESS SPRAY GUN OPERATION ReversibleSpray Tip TriggerMAJOR COMPONENTS OF SPRAY GUN AND REVERSIBLE SPRAY TIPSPRAY Attach spray gun to

1213AIRLESS SPRAY TROUBLESHOOTINGCoarse spray Low pressure Increase the pressure.Exces

1213REV-TIP™ SIZE SELECTION CHARTPATTERN WIDTH Thickness of the paint coat per stroke is determined by spray tip "fan width", r

1415Packing Tightening Procedure: Inspect the packing nut daily!If seepage of paint into the packing nut and/ or movement of the piston upw

1415SOLUTIONRell the supply container.Check for loose connections on the siphon assembly, tighten, then reprime pump.Tighten just enough t

1617Note: Check everything in the Troubleshooting Chart before disassembling the sprayer.FLUID PUMP DISCONNECTRefer to Fig. 301. Flush out

1617SERVICING INLET VALVE Refer to Fig. 18 & 301. Using a lightweight hammer, loosen then screw the suction nut (187- 084) off of t

21TABLE OF CONTENTSIntroductionDescription & Specifications... 1Safety Warnings ...

1819V-PACKING REPLACEMENTFIG. 20V-PACKING REPLACEMENT KIT (301-443)Refer to Figures 20 & 21Repack Kit contains all leather & plasti

1819V-PACKING REPLACEMENT (Continued) h. Metal male gland (187-025). Flat side down and round side up. i. Three plastic V-packings (1

2021V-PACKING REPLACEMENT (Continued)* Included in the Repack Kit (301-443), # Included in the Gland Kit (187-064), + Included in Piston As

2021PAINT SYSTEM ASSEMBLYFIG. 22176543210981117161514131295ITEM NO. PART NO. DESCRIPTION 1 120-504 ProLight

2223FIG. 23MANIFOLD FILTER - PN 111-200-991 111-202 Base 2 301-356 Spring3 106-007

2223PRIME VALVE FIG. 24STEP 1: Ensure that the pressure control knob (POT) is in the maximum (CW) position.STEP 2: Remove the upper and lo

2425REPLACEMENT OF ELECTRICAL CONTROL BOARD1. Remove electrical cover.2. Disconnect sensor lead from Electrical Board.3. Disconnect two clu

2425REMOVING CLUTCH Refer to Figures 25-311. Remove the gear box cover (Fig 30, item 1) by discon-necting the uid hose to the manifold l

2627CLUTCH REPLACEMENT (Continued) FIG. 26PARTS LIST FIGURE 26 1 301-231 Cog Belt 2 301-264 Clutch Replacement 3 305-088 Scr

2627176543298FIG. 28CLUTCH ASSEMBLY FIG. 27 56123 48 710 9GearboxENGINE ASSEMBLY FIG. 291 112-041 Screw-Differential

21 The SL6500 sprayer is the choice of the high volume contractors that need a machine that can pump extremely heavy materials like wall

2829POWER UNIT ASSEMBLY 1 301-320 Cover-Gearbox 2 301-531 Cover-Top3 301-13

2829FIG. 31FRAME ASSEMBLY SUCTION ASSEMBLIES (Optional)FIG. 321 301-201 Frame 2 301-202 Bra

30 AIRLESS ATOMIZER KIT (120-117)FIG. 331234567891011121314151617 HOPPER ASSEMBLY (331-441)121 301-442 Hopper Assy

23NOTE TO PHYSICIAN: Injection in the skin is a traumatic injury. It is important to treat the injury surgically as soon as poss

23TOXIC FLUID HAZARDHazardous uid or toxic fumes can cause serious injury or death if splashed in eyes or on skin, inhale

45WARNINGS - Continued WARNINGDo not use halogenated solvents in this system. The prime valve, 2 gun manifold an

45SETTING UP 3. Check the Engine Oil Levela. Unscrew the oil ll plug. The dipstick is attached to the plug.b. Without threading the p

675. Storage Oil-base paint: Flush with mineral spirits. Water-base paint: Flush with water, then mineral spirits and leave the

67HOW TO FLUSH WARNING: To reduce the risk of static sparking, which can cause re or explosion, always hold a metal part of the gun rmly